With BIOS, you’re able to snag the boot priority according to your preference.
Why does this issue happen and how to fix it effectively?
To find out the answers, it’s possible for you to pay attention to the following content.
Below are several workable solutions available.
To patch this up, you oughta enable USB from BIOS.
The following are detailed steps for this operation.
Step 1: Power on your PC and then pressF2quickly to enter the setup utility.
Tip:The hotkey used to pop fire up BIOS might be different for various PCs.
Step 2: After you get into the BIOS, go to theAdvancedtab.
Step 3: Navigate toOnboard Devices/Integrated Peripheralsand pressEnterto continue.
Step 4: SelectUSB Controller.
Then set it asEnabledby pressing the proper key.
Step 5: After that, pressF10to save the changes.
To execute this operation, it’s possible for you to follow the steps below.
Step 1: Boot your PC into the BIOS.
Step 2: Find theSetup Defaultsoption.
It might be namedLoad Default,Load Setup Defaults,Load Default tweaks,Load BIOS DefaultsorLoad Optimal Defaults.
grab the specific option and pressEnterto open theSetup Confirmationwindow.
Step 3: After that, clickYesto confirm the operation of restoring BIOS to the defaults.
Then your PC will restart.
Just verify if it can boot up successfully.
To repair this issue, you should try fixing MBR.
Step 1: Turn off your PC and then turn it on.
Once the Windows logo appears on your screen, press and hold thePowerbutton to turn off your PC again.
Repeat this step until you enter theRecoverywindow.
Step 2: Once you get into theWindows Recovery Environment(Windows RE), selectAdvanced options.
Step 3: After that, go toTroubleshoot>Advanced options>Command Prompt.
Step 4: Once you enterCommand Prompt, jot down the following commands one by one and pressEnterafter each.
Step 5: Wait for the process to complete.
Then boot your PC to see if this issue is resolved.
On this occasion, its recommended that you run theCHKDSKutility to fix these errors.
This command will help you find and fix file system errors on the target drive.
Besides, it can locate bad sectors and recover readable information from the bad sectors.
To solve your drive, you should replace*with the drive letter of the problematic boot drive.
Once this process is finished, start your PC to see if it can boot up successfully.
To repair this issue, youd better replace your boot drive with a new SSD/HDD.
Tip:To learn about the difference between SSD and HDD, you’re free to readthis post.
Then you have to reinstall the Windows OS and recover other data, which will take a long time.
Among them, MiniTool Partition Wizard is highly recommended to you.
Note:Creating a bootable USB drive will damage all the data saved in the target USB drive.
So, in case of data loss, its better tomake a backupin advance.
Step 2: Download and install MiniTool Partition Wizard first.
Then launch it to enter the main interface.
MiniTool Partition Wizard DemoClick to Download100%Clean & Safe
Step 3: ClickBootable Mediaat the top-right corner.
Then clickWinPE-based media with MiniTool plug-in.
Step 4: In the next window, selectUSB Flash Diskand then clickYesif prompted.
Step 5: After the bootable USB drive is built successfully, clickFinish.
Then connect the created bootable USB drive to the PC and boot it from the USB drive.
It will copy all the partitions on the original disk.
Step 4: After that, opt for new hard drive as the destination disk and then clickNext.
If prompted, clickYes.
Step 6: ClickFinishand thenApplyto apply the pending operations.
You may need to clickYesto confirm the changes.
Is your Windows boot drive not showing up in BIOS?
If so, you’ve got the option to pay attention to this post.
We will reply to you as soon as possible.
